ESD Floor Maintenance
ZeroStat Crete Fundamentals - Static-Conductive Water Based Epoxy Concrete Finish
Features:
- Economical, state of the art, permanent conductive formulation.
- Hard extended wear performance, never requires ESD Wax.
- Water based, easy application and cleanup
- Excellent chemical resistance.
- Extremely cost effective and NOT humidity dependant.
- Fast, low cost installation, minimal prep requirements.
- Lowest installation odor in the industry
- Available in the following colors:
ZeroStat Crete incorporates state-of-the-art, static conductive properties into a high performance, two-component, water-based epoxy for use on concrete and other hard surfaces. ZeroStat Crete provides outstanding durability and abrasion resistance while eliminating electrostatic charges which can damage or destroy sensitive electronics components or equipment.
ZeroStat Crete also displays superb resistance to a wide variety of chemicals and solvents commonly found in industrial and commercial environments, without the toxicity and disposal considerations associated with some solvent systems. When cured, ZeroStat Crete exhibits characteristics superior to solvent-based polyurethane, and rivaling those of solvent-based epoxy coatings. ZeroStat Crete produces superior results when used on all interior concrete, stone and ceramic surfaces.
SPECIFICATIONS:
| Standard color | Medium Gray, Low Glare Finish |
|---|---|
| Solids | 37% +/- 1% |
| Static Decay | .02 seconds |
| pH | 6.0 - 7.0 |
| Weight per Gallon | 9.5 - 9.6 pounds |
Hardness |
30 (Sward) |
| Static Conductive | 104-106 ohms |
| Viscosity | H - J (Gardner) |
| Solvents | Water - Glycol |
| Flash Point | 142°F |
| Dry Time | Touch; 7 hours, Moderate traffic; 12 hours, Full cure 7 days |
| Coverage | 250 - 600 ft2 per gallon |
APPLICATION & MAINTENANCE:
Overview:
New
concrete floors should be allowed to cure for thirty days. Applications
to floors
colder than 60°F is not recommended. Sweep and mop contaminated
floors with Brut, Grease Strip of Citru-Gest to remove oil, grease
and soil. With contaminated or exceedingly smooth troweled floors
follow by etching with Ground Zero Prepare, then thoroughly rinse
with water. If floor has been previously coated, a small area should
be cleaned and roughed up by a screen disking with a 80 grit screen.
Test ZeroStat Crete for adhesion, lifting etc. Any area's of the
existing coating which display poor adhesion should be stripped.
Wash the stripped
area's, acid etch, and rinse thoroughly. Allow the floor to dry.
Catalyzed ZeroStat Crete should be used within six hours of mixing,
therefore
prepare only the quantity necessary for immediate use. Add the
pre-measured catalyst to epoxy base. Stir gently until the catalyst
has been thoroughly
mixed in. Allow catalyzed mixture to stand 5 minutes. Apply catalyzed
ZeroStat Crete with a short nap roller in thin uniform coats. The
initial coat will cover approximately 250 to 500 ft2 per gallon.
Second coat coverage is approximately 400 to 600 ft 2 per gallon
. Note:
This product is not recommended for applications that experience
reoccurring standing water.
ZeroStat Crete is a thin set epoxy (approximately 3 to 7 mil thickness), much tougher and longer lasting that ESD paints. Due to it's reduced solids count and thin set benefits ZeroStat Crete may exhibit slight variances in texture and color. These variances do not affect the excellent electrical performance or wear characteristics. ZeroStat Crete is only available in Gray and features a non glare finish. For extended color options and fill applications (up to 125 mil thickness) please give us a call.
Ultra Con TM Elite - 2-LAYER High Temperature Rubber ESD Matting
Adjustable Elastic ESD Wrist Strap
